ReferenceDesignLibrary

Refine Search

Eval Board Current Out Voltage Out Supply Voltage Features Quiescent Current [Typical] Component Count + Extras Application / Target Market Design Author Main I.C. Base Part
Clear
Clear
Clear
Clear
Clear
Clear
Clear
Clear
Clear
Clear
Clear All Selections Apply Filters

Designs (7)

7 Results - Page 1/1

ISL6146BEVAL1Z: 50A @ 3 ~ 20V, OR-ing Controller

Manufacturer: Intersil

The ISL6146 represents a family of OR-ing MOSFET controllers capable of OR-ing voltages from 1V to 18V. Together with suitably sized N-channel power MOSFETs, the ISL6146 increases power distribution efficiency when replacing a power OR-ing diode in high current applications. It provides gate drive voltage for the MOSFET(s) with a fully integrated charge pump.

The ISL6146 allows users…

View Design

DC1676A: 20A OR'ing or Dual Diode, 4.5 ~ 60V in

Manufacturer: Linear Technology/Analog Devices

Demonstration Circuit 1676A showcases the LTC®4359 ideal diode controller with reverse input protection. The board includes two independent LTC4359 ideal diode circuits, sharing a common ground and operating over a 4.5V to 60V range. Each circuit comprises a load switch and ideal diode connected in series. Power to the load may be turned on and off by using the SHDN input, and the load is protect…

View Design

DC1926A: Dual Ideal Bridge Controller

Manufacturer: Linear Technology/Analog Devices

Demonstration circuit 1926A features the LTC4353, a dual low voltage ideal diode controller, in a typical 12A application. The LTC4353 creates two near-ideal diodes using external N-channel MOSFETs thereby replacing high power Schottky diodes and their associated heat sinks. Ideal diodes enable low loss power ORing and supply holdup applications.

The LTC®4353 controls external N-cha…

View Design

DC1203A: ORing 2 x 5A @ 48V (75V Max)

Manufacturer: Linear Technology/Analog Devices

Demonstration Circuit 1203 showcases two LTC4357s in a 48V, 5A application. The circuits are operational over a range of 9V to 75V and are fully independent, with the exception of a common ground.

Input and output connections are made by 93 mil turrets which if removed, accommodate insertion of up to 12 gauge wire for in-situ testing. Adequate copper is available for use up to 20A, w…

View Design

ISL6146AEVAL1Z: 50A @ 1~18V, 3 ~ 20V for Control

Manufacturer: Intersil

The ISL6146 represents a family of OR-ing MOSFET controllers capable of OR-ing voltages from 1V to 18V. Together with suitably sized N-channel power MOSFETs, the ISL6146 increases power distribution efficiency when replacing a power OR-ing diode in high current applications. It provides gate drive voltage for the MOSFET(s) with a fully integrated charge pump.

The ISL6146 allows users…

View Design

DC1899A-B: 12 V, 9 A OR'ing Controller

Manufacturer: Linear Technology/Analog Devices

Demonstration circuit 1899A controls two independent power rail circuits each with Hot Swap™ and ideal diode functionality provided by the LTC4228-1/LTC4228-2 dual ideal diode and Hot Swap controller.

DC1899A facilitates evaluation of LTC4228 performance in different operation modes such as supply ramp-up, power supply switchover, steady state, and overcurrent faults. Power supply sw…

View Design

ISL6146CEVAL1Z: 12V(typ), 50A OR'ing Controller

Manufacturer: Intersil

The three ISL6146 evaluation boards are used to demonstrate four application configurations. All the boards have ADJ shorted to VOUT with the PCB layout having the component footprints to insert a resistor of choice between ADJ and GND to adjust the HS COMP Vth. Likewise, the VIN is connected to BIAS but these can be separated to provide an adequate BIAS voltage when OR-ing <3V supplies or if …

View Design
7 Results - Page 1/1